bfc2 809 05... www.vishay.com vishay bccomponents revision: 04-aug-15 1 document number: 28529 for technical questions, contact: dc-film@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 film dielectric trimmers features ? high temperature type ? housing dimensions: ? 6 mm x 8 mm x 9 mm ? for a basic grid of 2.54 mm ? top and bottom adjustment ?round head ? mounting: radial ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 applications ? antennas ? impedance matching circuits ? medical ?rf ? for fine adjustment in professional applications quick reference data rated dc voltage 300 v dc test dc voltage for 1 min 600 v dc maximum contact resistance 5 m ? minimum insulation resistance between stator and rotor 10 000 m ? category temperature range -40 c to +125 c climatic category (iec 60068) 40/125/21 minimum storage temperature -55 c related specification iec 60418-1 and 4 effective angle of rotation 180 (rotation in 180 only, see life of trimmer) operating torque c max. < 3.5 pf 1 mnm to 15 mnm c max. ? 3.5 pf 1 mnm to 20 mnm maximum axial thrust 2 n capacitance range (c min. / c max. ) 1.2 pf / 3.5 pf to 2 pf / 18 pf life of trimmer maximum 10 cycles: rotation in 180 on ly (the electrical and mechanical performance is not guaranteed if rotated beyond 10 cycles) quality level sampling and data evaluation for quality level in accordance with mil-std-105d and iec 60410 : < 0.15 % major defects < 0.65 % minor defects each capacitor is tested for minimum c max. and is also subjected to the full test voltage.
bfc2 809 05... www.vishay.com vishay bccomponents revision: 04-aug-15 2 document number: 28529 for technical questions, contact: dc-film@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions in millimeters trimmers bfc2 809 05... series, with round heads hole pattern adjustment for top adjustment a screwdriver or tri mming key can be used; for bottom adjustme nt a key is requir ed as shown below. bottom adjustment key 5.08 0.2 3.7 0.2 1.1 0.2 9 max. ? 2.2 ? 2.2 z 0.6 0.5 min. 1.1 max. color mark s prue 0.6 0.1 0.85 max. 0.5 0.15 ? 1.4 detail z turned 90 3 0.2 6.4 max. 6.7 max. 7.4 max. 1.2 (2 x) 1.9 5.08 2.3 0.1 r s ? 2.2 2 min. 0.6 + 0.2 0 ? 1.5 + 0.1 0 0.7 + 0.1 0
bfc2 809 05... www.vishay.com vishay bccomponents revision: 04-aug-15 3 document number: 28529 for technical questions, contact: dc-film@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 mounting the trimmer can be mounted on printed-circuit bo ards with a minimum hole diameter of 2.54 mm. packaging blister packs of 70 units each. for smallest packaging quantity (spq) see electrical data table. note (1) c: 60 % to 80 % of c max. ; t amb : from +20 c to +125 c soldering conditions for general soldering conditions and wave soldering profile, we refer to the applicat ion note soldering guidelines for film capacitors: www.vishay.com/doc?28171 ordering information c min. / c max. (pf) catalog number bfc2 809 05... top and bottom adjustment round head round head and flux guard 1.2 / 3.5 215 001 1.8 / 10 216 002 2 / 18 217 003 electrical data guaranteed max. c min. / min. c max. at 200 khz (pf) shape of head fig. tan ? at c max. x 10 -4 temp. coeff. (1) (10 -6 /k) min. f res at c max. (mhz) col. of dot spq catalog number bfc2 ... ..... 1 mhz 100 mhz 1.2 / 3.5 round 1 ? 10 ? 20 -250 350 850 orange 700 ....?809?05001 700 ....?809?05215 1.8 / 10 round 1 ? 10 ? 20 -250 350 1200 none 700 ....?809?05002 580 white 700 ....?809?05216 2 / 18 round 1 ? 10 ? 25 -250 350 360 red 700 ....?809?05217 700 ....?809?05003 test procedures and requirements iec 60418-1 clause iec 60068 test method test procedure r equirements 4.2 method of mounting method a 14 capacitance drift after tc measurement ? c/c: ? 2.5 %; 4 % for 2?pf 19 thrust axial thrust of 2?n ? c/c: ? 0.3 % 21 robustness of terminations: ? 21.1 ua tensile 1?n no damage ? 21.2 ub bending 1 cycle no damage 22 na rapid change of temperature 1 cycle; 0.5 h at lower and ? 0.5 h at upper category temperature ? c/c: ? 2.5 % 23 t soldering: ? ta solderability solder bath immersion 3?mm; 235?c;?2?s good wetting, ? no mechanical damage ? tb resistance to heat solder bath : 260?c;?10?s no mechanical damage
bfc2 809 05... www.vishay.com vishay bccomponents revision: 04-aug-15 4 document number: 28529 for technical questions, contact: dc-film@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 24 eb impact bump 4000 10?bumps; 40?g;?6?ms ? c/c: ? 0.6 %; ? no mechanical damage 25 fc vibration frequency 10?hz to?55?hz; ? amplitude 0.35?mm; ? 1.5 h ? c/c: ? 0.6 %; ? no mechanical damage 26 climatic sequence: ? c/c: ? 2.5 ? 26.1 b dry heat 16?h at upper category temperature tan ? : ? 10 x 10 -4 for c max. < 18?pf; ? tan ? : ? 40 x 10 -4 for c max. ? 18?pf ? ? r ins. : ? 10 000?m ? ; ? rotor contact r: ? 5?m ?? 26.2 d damp heat accelerated, ? first cycle 1 cycle; 24 h; +40?c; ? 95?% to?100 % rh voltage proof: ? 600?v for 1?min ? 26.3 aa cold 16?h; -40?c visual examination: ? no mechanical damage ? 26.5 damp heat accelerated, remaining cycles 1 cycle; 24 h; +40?c; ? 95 % to 100 % rh operating torque: ? 1?mnm to?20?mnm 27 ca damp heat steady state 21?days; +40?c; ? 90?% to?95 % rh ? c/c: ? 2.5 % ? ? tan ? : ? 10?x?10 -4 for c max. < 18?pf; ? tan ? : ? 25?x?10 -4 for c max. ? 18?pf ? ? r ins. : ? 10 000?m ? ; ? rotor contact r: ? 5?m ?? ? voltage proof: ? 600?v for 1?min ? ? visual examination: ? no mechanical damage ? ? operating torque: ? 1?mnm to?20?mnm 29 mechanical endurance 10?cycles ? maximum 10 cycles: rotation in 180 only (the electrical and mechanical performance is not guaranteed if rotated beyond ? 10 cycles) ? c/c: ? 0.3 %; ? 2.5 % for 2 pf ? ? c/c after axial thrust: ? 0.3 %; ? rotor contact r: ? 5?m ?? ? voltage proof: ? 600?v for 1?min ? ? visual examination: ? no mechanical damage ? ? operating torque: ? 1?mnm to?20?mnm test procedures and requirements iec 60418-1 clause iec 60068 test method test procedure r equirements
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
